Home Builder Developer - Interior Renovation and Design

Project detailsSkill1 out of 5EasyThe sheets are heavy and a bit unwieldy, especially when covering the ceiling.Cost

$8 to $10 per -inch x 48-foot sheet

6 to 8 hours

Call it wallboard, plasterboard, Sheetrock, or just plain rock, like some pros do, drywall revolutionized the way walls and ceilings are covered. Before the 1950s, when these paper-wrapped gypsum panels came into widespread use, it took days for lathers and plasterers to create a firm, flat foundation for paint or wallpaper. With drywall, it takes a fraction of the time. Two pros can typically cover a 12-by-16-foot room in about an hour.

To work that fast takes practice and a few specialized tools. But hanging drywall is not just about speed. Doing the job right means using screws of the correct length, off-setting panels so seams dont line up, and making sure wires and pipes arent vulnerable to puncture.

Installing drywall is easy enough for a homeowner, as long as theres someone to help; the heavy sheets are difficult to lift, particularly when doing ceilings. Follow the drywalling tips below to learn how to hang drywall like a pro.

Despite their drab, if-youve-seen-one-youve-seen-them-all appearance, these flat sandwiches of gypsum plaster and recycled newsprint come in a variety of types and sizes to suit the specific demands of a job.

There are 14-inch-thick flexible panels to cover a curved wall or ceiling and 58-inch-thick abuse-resistant panels that are less likely to develop holes or dents. Greenboard keeps its integrity in the face of high humidity, making it a good choice for bathrooms. Type X resists fire, making it well-suited to furnace rooms and between-floor chases.

Massachusetts contractor Paul Landry often installs blueboard, so-called because of its indigo paper. It bonds tenaciously with veneer plaster, a finish much in demand in Landrys area. The light-gray product known as drywall is the type in widest use.

When butted end-to-end, its factory-beveled lengthwise edges form a shallow swale for a topping of joint compound and tape. Half-inch is the preferred thickness for walls and ceilings; 58-inch works best if studs or joists are 24 inches apart, where thinner drywall would sag. The sheets most commonly available in hardware stores measure 4 by 8 feet, but lengths can reach up to 16 feet and widths up to 54 inches, which speeds the installation and minimizes the number of seams.

Bigger panels have their downside, however: Theyre heavy and unwieldy. A 12-foot sheet of -inch drywall weighs about 80 pounds, nearly 30 pounds more than a standard 8-foot panel. Thats why manufacturers have developed 38-inch thick gypsum panels that weighs 16 percent less than standard sheets. These, however, are used only to cover existing drywall.

PLANNING AHEAD

Tip: Add a screw next to any screw head that breaks the paper.

Read the rest here:
How to Hang Drywall in 8 Steps - This Old House

Installing drywall is not rocket science, but it will go faster and look better if you learn the fundamentals before you start (instead of after you're done).

Drywall is one of the easiest-to-use and cheapest construction materials in the world. Even a serious mistake will make you chuckle, knowing youve wasted little time and probably less than five bucks. And the money you save handling the task yourself will come in handy when furnishing that new room.

Hanging rock (short for sheetrock) doesnt require a lot of finesse, but it is heavy work. But if you are in reasonably good physical condition, dont be afraid to tackle one, two or even three rooms on your own. Its sometimes hard to interest a pro in hanging just a room or two, or even get on the schedule. Besides, defining and covering the walls with a finished material can be satisfying.

This how to install drywall article will demonstrate the basics of hanging drywall. If you do a good job of hanging drywall, the drywall can be taped and finished smoothly and easily. Taping refers to the process of filling fastener holes, applying joint tape and three layers of taping compound to seams and corners, and then sanding. (Read more about drywall taping here.) Poor drywall hanging techniques make it difficult for even a seasoned taper to deliver a flat, uncracked surface thats free of nail pops and ready for paint. Well show you the techniques and tools the pros use to get the drywall job done fast and in a way that makes taping as painless as possible.

Continue reading here:
How to Hang Drywall Like a Pro (DIY) | Family Handyman

A Versatile Construction ServiceOur company is a well-known provider of various services for your home construction of drywall, additions, renovations, remodeling, and more. But we dont stop with just that. Our years of experience made us highly skilled professionals who are able to build new, custom homes. Thats right, we make the designs of our clients come to life and build the homes that they want to live in or sell for a profit. Whatever you need for your new home, we will do it. Share the details of your plans and before long, you will see us completing your project with flying colors.

Our ServicesAs the name of our drywall company suggests, we specialize in drywall installation and repairs. Besides that, we offer remarkable painting solutions for both exterior walls and interior living spaces. We use incredible faux painting techniques that add many features to your property. If you are looking to add a touch of intimacy or warmth to your bedroom, our finishes will turn your bare walls into any kind of texture you would like to replicate, including Venetian plasters, stripes, and much more. Whether it comes to a one-time, residential drywall repair service, or a big commercial remodeling project, we are ready and eager to assist you!

See the original post:
Local General Contractor - Garcia and Sons Construction LLC

Sure, retaining walls look like simple stacked stone, block, or timber. But in fact, theyre carefully engineered systems that wage an ongoing battle with gravity. They restrain tons of saturated soil that would otherwise slump and slide away from a foundation or damage the surrounding landscape.

These handsome barriers also make inviting spots to sit, and can increase usable yard space by terracing sloped properties, something that is increasingly important as flat home sites become ever more scarce in many regions.

Along with sloped landscapes where water runoff causes hillside erosion, ideal locations for a retaining wall system include spots downhill from soil fault lines and where the downhill side of a foundation is losing supporting soil or its uphill side is under pressure from sliding soil.

If your property needs a retaining wall, or if the one you have is failing, follow our guide on how to build a retaining wall or hire a pro. We also review the four most common types below: timber, interlocking blocks, stacked stone, brick or block, and concrete.

Although retaining walls are simple structures, a casual check around your neighborhood will reveal lots of existing walls that are bulging, cracked, or leaning. Thats because most residential retaining walls have poor drainage, and many arent built to handle the hillside theyre supposed to hold back.

Even small retaining walls have to contain enormous loads. A 4-foot-high, 15-foot-long wall could be holding back as much as 20 tons of saturated soil. Double the wall height to 8 feet, and you would need a wall thats eight times stronger to do the same job.

With forces like these in play, you should limit your retaining wall efforts to walls under 4 feet tall (3 feet for mortarless stone). If you need a taller wall, consider step-terracing the lot with two walls half as big, or call in a landscape architect or structural engineer for the design work (have the architect or engineer inspect the site thoroughly) and experienced builders for the installation.

If you have your retaining wall built, figure about $15 per square face foot for a timber wall, $20 for an interlocking-block system or poured concrete, and $25 for a natural-stone wall. Preparing a troublesome siteone that includes clay soil or a natural spring, for examplecan raise costs substantially. Add 10 percent or so if you hire a landscape architect or engineer. But shop around; some landscape firms do the design work for free if they do the installation.

Poor drainage resulting in saturated soil and frost heaving is the main cause of failure. Thats why all strong retaining walls begin with landscape fabric, backfill, and 4-inch perforated drainpipe.

The depth you need to excavate depends on frost depth as well as the wall and soil type. Mortared or concrete walls in heavy-frost areas require footings dug below the frost line. Nonmortared walls should be built on a gravel-filled trench dug below frost line. If you live where it doesnt freeze and your soil drains well, you may be able to just scrape away topsoil to form a base for nonmortared walls.

Before adding gravel, lay down enough landscape fabric to contain the new gravel. Form the fabric into a large C shape, with the open mouth of the C facing downhill. The fabric should wrap around and create a border between the gravel and topsoil to keep sediment from clogging the gravel and drainpipe.

Replace native soil with 3/4-minus gravel (no stones under 3/4 inch in diameter) or bank-run gravel (washed stones 1/4 inch to 6 inches in diameter). Shovel at least a 4-inch layer of gravel onto the landscape fabric. Grade this layer so it slopes 1 inch for every 4 feet, allowing water to drain away. Then lay in 4-inch perforated PVC drainpipe at the base of the wall and cover it with gravel.

Shovel in backfill as you build the wall, one tier at a time. Dont add all the backfill at the endit wont compact thoroughly. Tamp down the gravel as you go with a heavy hand tamper. Behind the top tier of the wall, add 6 inches of topsoil and lightly compact it.

All retaining walls should lean into the hill 1 inch for every 12 inches of height. Timber walls 4 feet or higher should be tied to the hillside with deadmen anchors (6-foot-long, T-shaped tiebacks buried in the hillside) attached to the wall every 8 feet, extending 6 feet back to a 2-foot-wide T-bar.

Deadmen are not included in some interlocking-block systems if the design allows backfill to secure the blocks individually in place. Still others require geo-grid, weblike tiebacks that get buried in the backfill. Check the manufacturers literature.

A final heads-up on masonry wallsconcrete blocks chip and crack easily. Carefully inspect the blocks upon delivery, and dont be shy about returning damaged blocks for credit.

Upside: Strong. Well-designed and properly drained and backfilled, concrete walls rarely fail.

Downside: Bare concrete isnt particularly attractive. It can be veneered with masonry, or special forms can be used that embed decorative designs in the finished wall. Also, if a wall fails, patching may not be possible and removal is costly. Walls over a few feet high should be formed and poured by a pro unless youve had experience with vertical pours.

Cost: Around $16 to $20 per square face foot installed.

Remember:

Follow all rules for landscape fabric, drainage, and backfill. The footing should be below frost depth or on well-drained gravel that reaches this level. Use 3/4-inch ply and 2-by-4 bracing to form the wall. And install #4 rebar wired in 12-inch grids for added strength. Use mechanical vibration or strike the forms with a rubber mallet every 6 inches when concrete is wet for a smooth finished face.

Upside: Only moderately challenging to build by yourself up to 4 feet high. If an engineer has designed the wall, located the deadmen, and specified the backfill and drainage, you can install an even taller wall yourself.

Downside: Not as long-lived as masonry. Making square cuts is challenging. Also, components are heavy and hard to manage alone. Plan on about three days to build a wall 4 feet tall by 15 feet long.

Cost: $10 to $15 per square face foot installed, depending on your regionhigher if extensive excavation, soil prep, and backfilling are needed.

Remember:

Use 8-foot-long, 66-inch pressure-treated wood designated For Ground Contact, and have all materials delivered. Follow all rules for landscape fabric, drainage and backfill. All timber walls require deadmen every 4 feet at midwall height or higher. Pin the first tier of timbers to the ground with #4 rebar.

Upside: Also called segmented retaining walls, interlocking-block systems from Keystone, Risi, Rockwood, Tensar, Versa-Lok, and others are mortar-free and easy to assemble. Units are small and modular, so walls can taper, turn, wrap, and curve. Available in many textures, shapes, and colors, these engineered systems, which can be used for walls up to 20 feet high, rely on several techniques including:

Downside: You cant mix and match manufacturers systems. Block systems that use metal pins to tie blocks together can be a challenge to line up exactly.

Cost: About $12 to $20 per square face foot installed, depending on block configuration and site. More expensive systems tend to be stronger and stack higher.

Remember:

Arrange before delivery from the masonry yard where materials will be stockpiled in your yard and if the forklift used to off-load the truck will fit through backyard gate, etc. Follow all rules for landscape fabric, drainage, and backfill. Use manufacturers calculators to determine how many blocks, pins and tiebacks youll need. When stacking a row of blocks, sweep off each layer; small pebbles can disrupt the pattern. Cap walls with flat units or stone held down with silicone caulk.

Upside: For a stone retaining wall, a handsome rustic appeal. Collecting stones on site and doing the work yourself can also save money. Brick provides a more formal look. Cinder block is inexpensive and can be reinforced with steel and concrete.

Downside: Stone-wall masonry is harder than it appears. Fitting the stone is exacting work and making mortar joints look natural requires experience (nonmortared stone walls dont offer much holding power). Brick masonry also requires skill to hit the visual standard all of us are used to. Cinder block has to be faced with stucco, brick, or stone or overgrown with plantings to make it attractive.

Cost: About $10 to $12 for cinder block; for brick and stone, around $20 to $25 per square face foot (double that figure for a two-sided wall).

Remember:

Follow all rules for landscape fabric, drainage, and backfill. A mortared wall needs a footing and a drainage system that will defeat frost heaving. A dry, nonmortared wall allows water to seep through, relieving pressure behind the wall naturally.

Retaining walls usually fail slowly. Common problems can often be fixed if you act quickly. You can also protect a new wall in the building process by safeguarding it against the three most common failures:

What happens: A load is added within 3 feet of the top of the wall. The wall leans out at the top and eventually tips over

What to do: Tell your landscape architect or engineer if a car or shed will be placed near the wall. The pro should then beef up the footer and increase the number of tiebacks or deadmen to add strength. Adding retrofit tiebacks is expensive and requires excavation, partial dismantling, and reengineering the wall.

What happens: Soil behind the wall gets saturated, causing hydrostatic water pressure and weight to topple the wall.

What to do: Replace native soil behind the wall with 3/4-minus or bank-run gravel for 2 feet. Line the inside base of the wall with 4-inch perforated tile drain on a gravel bed that slopes 1 inch for every 4 feet of run to carry water to daylight or a dry well. Topsoil should take up only the top 6 inches behind the wall.

What happens: Retaining wall lacks proper drainage or a footer. Soil becomes saturated and freezes, heaving upward and breaking the wall apart.

What to do: Walls should rest on 3/4-minus or bank-run gravel, with the footer or wall base buried beneath the frost line (6 to 48 inches, depending on region). For deep frost, use concrete block rather than retaining wall to ground level, then build the retaining wall on that. Well-drained gravel behind and beneath the wall can substantially diminish frost heaving.

Hickson Inc.

1955 Lake Park Dr., Suite 250

Smyrna, GA 30080

http://www.hickson.com

770-801-6600

Keystone Retaining Wall Systems

4444 West 78th Street

Bloomington, MN 55435

http://www.keystonewalls.com

800-747-8971

Osmose Wood Preserving

1016 Everee Inn Rd., Box O

Griffin GA 30224-0249

http://www.osmose.com

770-228-8434

Risi Stone Systems

8500 Leslie St., Suite 390

Thornhill, ON L3T 7P1 Canada

http://www.risistone.com

800-626-9255

Rockwood Retaining Walls, Inc.

7200 N. Highway 63

Rochester, MN 55906

http://rockwoodwalls.com

800-535-2375

Tensar Earth Technologies

5775-B Glenridge Dr., Lakeside Center, Suite 450

Atlanta, GA 30328

http://www.tensarcorp.com

800-836-7271

Versa-Lok Retaining Wall Systems

6348 Highway 36, Suite 1

Oakdale, MN 55128

http://www.versa-lok.com

800-770-4525

Continued here:
Retaining Walls: How to Build Them, Costs & Types - This Old House

Stranded By Storms, Neighbor Keeps Mountain Community Connected With Outside World Thanks to Zipline  NBC Bay Area

See original here:
Stranded By Storms, Neighbor Keeps Mountain Community Connected With Outside World Thanks to Zipline - NBC Bay Area

Organization offering hotline, helping with clean up efforts in Wynne  KATV

Visit link:
Organization offering hotline, helping with clean up efforts in Wynne - KATV

Our Carpet Cleaning PackagesBasic Package

Clean

In ourBasic Package, your carpets will get a healthy deep cleaning, using our innovative Hot Carbonating Extraction (HCE) process.

This process penetrates to the base of carpets to lift and whisk away dirt, grime, and non-living allergens. By removing these contaminants, we not only improve the appearance of carpets we also improve the health of your home!

Clean + Protect

OurStain Fighter Packagegives you the same deep clean as our Basic Package, plus the added benefits of a protectant.

With this package, we apply a protective stain-fighting solution during the cleaning process. This allows the protectant to coat carpet fibers, boosting your carpets stain-fighting power.

If youre worried about existing stains, we also offer aspecialty stain removal service for carpeting and upholstery. Our stain removers can handle tough stains from sources like wine, lipstick, permanent marker, grass, and more!

Clean + Protect + Anti-Allergen + Deodorize

TheFresh & Healthy Home Premium Packageoffers our deepest possible clean for your home.

In this package, you get the deep clean offered by our Basic Package, the protectant from our Stain Fighter Package, plus an anti-allergen and odor removal treatment for your carpets.

Rather than simply masking lingering smells, we eliminate odors at the source. At the same time, we reduce common household non-allergens and improve indoor air quality, creating a fresher and healthier home!

Our unique cleaning process is not only trusted by thousands of homeowners it also bears the Carpet & Rug Institutes Seal of Approval!

The Seal of Approval is an independent program that grades carpet cleaning products and systems. It measures factors like how well cleaning tools and products remove soil from carpets, how long it takes for carpets to resoil after cleaning, and whether the system causes damage or discoloring to carpet fibers.

Our Hot Carbonating Extraction system was awarded the Platinum Seal of Approval. The Platinum Seal of Approval is thehighest level awarded to carpet and rug cleaning systems!

Thanks to the Seal of Approval program, homeowners know that Chem-Dry cleaning systems deliver a cleaner, healthier, and longer-lasting carpet!

Ready to bring a deeper, healthier clean to your carpets? Enter your ZIP code below to find your nearest Chem-Dry location!

Read more here:
Carpet Cleaning - Find Local Carpet Cleaners | Chem-Dry

Carpet adds texture, color and warmth to a home, but daily use can cause stains, as well as trap dust and allergens. While regular vacuuming is the first step in cleaning carpets, an annual deep clean is recommended to help extend the life of your carpet and keep your home looking clean.

Understanding how to clean carpets starts with discovering that there are different types of machines available. Whether you need an upright carpet cleaner or a steam cleaning machine, you can buy or rent carpet cleaners based on your specific need.

When it comes to cleaning carpets, there are also a variety of floor cleaning solutions for each method. From all-purpose cleaners to those with added features like stain repellents, low-foam agents or deodorizers, there are a variety of ways to tackle whole house carpet cleaning and specific stains. Follow this easy plan to make cleaning carpet at home easier.

See the article here:
How To Clean Carpet - The Home Depot

When installing new carpet, start by taking accurate measurements of the room. Measure the length and width of the room. Multiply these measurements together to find the square footage.

Carpet is measured in square yards. One square yard is 9 square feet. To convert square feet to square yards, divide the square footage by 9. Example: 90 square feet/9 = 10 square yards

If the room isnt a perfect rectangle, measure the room's square footage in sections. Then, add them together to find the total square footage. This guide covers how to put carpet down in a room thats square or rectangular.

Once you have measured your room, order the carpet. Order 10 to 20 percent more carpet than you need to be sure you have more than enough to cover the floor. You'll also need to get tools and flooring supplies, like tack strips, adhesives and edging, for your carpet installation project.

See more here:
How to Install Carpet - The Home Depot

9125 Behner Brook Ct. Indianapolis, Indiana 46250

1729 S East St Indianapolis, Indiana 46225

6440 Michigan Rd Indianapolis, Indiana 46268

2001 Southeastern Ave Indianapolis, Indiana 46201

8801 CRAWFORDSVILLE RD Indianapolis, Indiana 46234

4084 PENDLETON WAY # 121Indianapolis, Indiana 46226

6008 N Oakland Ave Indianapolis, Indiana 46220

478 South Kenmore Road Indianapolis, Indiana 46219

10126 Alexia Dr Indianapolis, Indiana 46236

5602 ELMWOOD AVE STE 114 Indianapolis, Indiana 46203

1823 Lilac Dr Indianapolis, Indiana 46227

6317 Evanston Ave Indianapolis, Indiana 46220

8001 S Meridian St Indianapolis, Indiana 46221

7676 Zionsville Rd Indianapolis, Indiana 46268

7353 N SHADELAND AVE Indianapolis, Indiana 46250

5639 Hardegan St Indianapolis, Indiana 46227

10337 Liverpool way Indianapolis, Indiana 46236

5149 N Keystone Ave Indianapolis, Indiana 46205

1025 N RIDGEVIEW DR Indianapolis, Indiana 46219

3705 N HARTMAN DR Indianapolis, Indiana 46226

5639 Woodside dr Indianapolis, Indiana 46228

2123 ROSEDALE DR Indianapolis, Indiana 46227

10544 Stillwood Ln Indianapolis, Indiana 46239

5508 Elmwood Ave 411Indianapolis, Indiana 46203

446 CECIL AVE Indianapolis, Indiana 46219

7638 S. meridian ST Indianapolis, Indiana 46217

6935-A LAKE PLAZA DR Indianapolis, Indiana 46220

7418 Madison Ave Indianapolis, Indiana 46227

5602 Elmwood Ave Ste 203 Indianapolis, Indiana 46203

8765 Hague Rd Indianapolis, Indiana 46256

5840 W 71st Street Indianapolis, Indiana 46278

5352 N Tacoma Ave Indianapolis, Indiana 46220

8517 Westfield Blvd Indianapolis, Indiana 46240

2104 E 69th Street Indianapolis, Indiana 46220

8603-B ALLISONVILLE RD Indianapolis, Indiana 46250

11 N Arlington Ave Indianapolis, Indiana 46219

5303 W 79th St Indianapolis, Indiana 46268

6301 E 32ND COURT STE BIndianapolis, Indiana 46226

1520 Brookville Crossing Drive Indianapolis, Indiana 46239

3236 W SOUTHPORT RD Indianapolis, Indiana 46217

2314 N. Auburn St Indianapolis, Indiana 46224

PO Box 503144 Indianapolis, Indiana 46250

723 EAST NEW YORK ST Indianapolis, Indiana 46202

1010 East Banta Road Indianapolis, Indiana 46227

4258 PISA CT Indianapolis, Indiana 46235

1463 N SHANNON Indianapolis, Indiana 46201

8847 Commerce Park Pl Suite JIndianapolis, Indiana 46268

7252 E 86th St Indianapolis, Indiana 46250

11125 Monroe Ct Indianapolis, Indiana 46229

606 N RURAL Indianapolis, Indiana 46201

4818 FARRINGTON AVE Indianapolis, Indiana 46201

4600 E 16TH ST Indianapolis, Indiana 46201

3217 N SHADELAND AVE Indianapolis, Indiana 46226

7301 GEORGETOWN RD 208Indianapolis, Indiana 46268

8747 Fielding Ln Indianapolis, Indiana 46239

6311 E Shelbyville Rd Indianapolis, Indiana 46237

8481 Bash St 1600Indianapolis, Indiana 46250

6345 W Thompson Rd Indianapolis, Indiana 46221

6535 Guion Rd Indianapolis, Indiana 46268

5941 radnor rd Indianapolis, Indiana 46226

4030 Madison Ave Indianapolis, Indiana 46227

3605 Brandenburg Blvd Indianapolis, Indiana 46239

2720 E COUNTY LINE RD Indianapolis, Indiana 46227

8965 MADISON AVE Indianapolis, Indiana 46227

8502 Brookville Rd Indianapolis, Indiana 46239

12115 KINGFISHER CIR Indianapolis, Indiana 46236

5610 Crawfordsville Rd Suite 2301Indianapolis, Indiana 46224

703 S KAPPES ST Indianapolis, Indiana 46221

800 E Thompson Rd Indianapolis, Indiana 46227

5858 Thunderbird Rd Indianapolis, Indiana 46236

2817 MASSACHUSETTS AVE Indianapolis, Indiana 46218

7226 E 87TH ST STE D-1Indianapolis, Indiana 46256

5255 WINTHROP AVE Indianapolis, Indiana 46220

5865 common circle Indianapolis, Indiana 46220

1131 Shelby St Indianapolis, Indiana 46203

1423 Brewster Rd Indianapolis, Indiana 46260

6418 BRAMSHAW RD Indianapolis, Indiana 46220

50 N Illinois St Apt 211Indianapolis, Indiana 46204

4841 Industrial Parkway Indianapolis, Indiana 46226

9810 Rawles Ave Indianapolis, Indiana 46229

6245 KINGSLEY DR Indianapolis, Indiana 46220

8550 N MICHIGAN ROAD Indianapolis, Indiana 46268

4029 MATHEWS AVE Indianapolis, Indiana 46227

4230 E FALLCREEK PKWY N DR Indianapolis, Indiana 46205

7053 Grosvenor Place Indianapolis, Indiana 46220

1810 E 75TH PL Indianapolis, Indiana 46240

4505 E 82nd St Indianapolis, Indiana 46250

2176 N Meridian St Indianapolis, Indiana 46202

406 CAROLINA CT Indianapolis, Indiana 46217

6230 Southeastern Ave Indianapolis, Indiana 46203

4444 S Emerson Ave Indianapolis, Indiana 46203

6829 Hawthorn Park Dr Indianapolis, Indiana 46220

5505 S Meridian St Indianapolis, Indiana 46217

3425 Gerrard Ave Indianapolis, Indiana 46224

4201 Millersville Rd Indianapolis, Indiana 46205

2601 E 56th St Indianapolis, Indiana 46220

7505 Terrace Bch Indianapolis, Indiana 46240

8847 E MICHIGAN ST Indianapolis, Indiana 46219

1342 S East St Indianapolis, Indiana 46225

PO BOX 31005 Indianapolis, Indiana 46231

Continued here:
Top 10 Best Carpet Installation in Indianapolis, IN | Angi