5" & 6" ALUMINUM RAIN GUTTERS

Our goal here at A-1 Seamless Gutters is to give our customers the best looking and strongest seamless gutter systems out there!!! Our reputation depends on it. Happy customers keep us busy. CUSTOMERS AMAZED AT WHAT WE CAN DO FOR THEM IS WHAT KEEPS US ON TOP.

Locally owned and operated since 1989

Call us today 207-946-4999

Or use the information below to call us

Fill the form below and we can contact you

Our copper gutters are made from 16oz. or 20oz. copper. Our copper is pure, not plated. Gutter caps, outlets and down spouts are copper. Hangers will be copper and or brass depending on type for strength. Screws are stainless steel and or copper.

Our aluminum gutter systems are made from .032 primary aluminum. This is the thickest and strongest aluminum available for seamless gutters. All standard colors are baked on enamels so they will not fade, peel or crack. 90% of our gutters are installed with modified hidden hangers. These hangers are incredibly strong and not seen from the ground.

Keeping your gutters clean is keyto assure theypreformat 100%, and continueprotecting your house. We offer three levels of Gutter protection to help with this task.

A-1 SEAMLESS GUTTERS is NOT a franchise

5" & 6" COPPER SEAMLESS GUTTERS

Toll free at: 877-375-4888

Toll Free at: 877-375-4888

Link:
Gutter Installation - A-1 Seamless Gutters

Ashburn VA Gutter Cleaning Gutter Repair Gutter Covers Gutter Installation In Ashburn

Gutter cleaning in Northern, VA is a daunting task, but Gutterman Services is up for the challenge! The natural beauty of this area is breathtaking, but so is the mess of leaves and debris it leaves behind in your gutters. Maintaining gutters which are clean and free of obstruction is an important part of keeping a clean house or office.

Since 1986, we at Gutterman Services have been the premier gutter cleaning company in Ashburn. Armed with experience and knowledge, we have provided the best gutter services in the area for over twenty years! We can clean, screen, repair and replace any gutter, and will do it all while providing the best service youve ever experienced.

Our standard gutter cleaning service includes:

Gutterman Services also helps keep our clients on a schedule and provides a maintenance contract for our gutter cleaning services so you never have to worry about the state of your gutters. This allows you to rest assured that your regular maintenance is on Gutterman Services calendar and that we are staying on top of regular gutter cleaning and upkeep.

If your gutters are clogged and you do not get them cleaned water could back up into your house, causing significant damage. Dont leave the cleanliness of your gutters to chance! Contact Gutterman Services for all of your gutter cleaning needs in the Ashburn, VA! Protect your property investment today, contact onlineor call and speakwith a Gutterman Services representative today. Always feel free to call us at 571-297-1445. Dont wait for your gutters to back up, perform regular gutter maintenance with Gutterman Services!

Read more:
Ashburn VA Gutter Cleaning - Gutter Repair - Gutter ...

When it comes time to installing or replacing gutters, its important to refer to a specialist to get good advice. Several options are available, depending on the area where the home is located, its style, your budget and your tastes.

The primary role of gutters is to prevent water infiltration. Gutters collect water dripping on the roof and channel it away from the home. Without a gutter system, water will fall near the foundations, thus increasing the risk of water infiltration. Furthermore, without gutters, water will fall heavily and ruin flowerbeds.

Several types of fasteners are available in order to keep gutters attached to the home. Several options are available to you, depending on the roof type and its requirements. These are the major types of fasteners.

Nails are a basic attachment system and are especially used for fastening aluminum gutters. Its the most economical solution, but its major disadvantage is that it leaves rust lines with time, as well as being visible on gutters.

The spaced hanger is another popular alternative and its main advantage is that it is invisible from the ground. Although more expensive than nails, it offers a more attractive look to the gutter.

Equivalent to spaced hangers including an integral screw, this type of hanger is much easier to install, and is also invisible from the ground.

Slightly more expensive, the continuous hanger is the most solid fastening system out there. It protects the gutter from the weight of snow and ice. In addition, as it closes the gutter, it decreases the amount of maintenance required to clean the eavestrough in order to prevent clogs that cause water infiltration.

Gutters can be made from many different types of materials. Depending on the robustness desired and especially the desired style, several options are available on the market.

Copper is very durable and rust-resistant, and is the preferred choice for owners of old homes. However, this option is more costly and it must be taken into consideration that the color becomes dull and greenish with time.

Galvanized steel, which is a lot more affordable, is less attractive and ends up rusting; however, it is robust and durable.

Aluminum is the most popular material and very versatile since it is available in numerous colors, and several profiles and widths.

Vinyl gutters are generally chosen for their low cost; however, vinyl is not very resistant to intense cold in addition to losing its luster or changing color due to exposure to the sun.

When the time comes to select gutters to be installed in a home, we must ask whether we want seamless or sectional gutters. However, you might not have a choice depending on the material you choose for your gutters. Sectional gutters can often leak if they are not properly sealed. Furthermore, seamless gutters offer a more finished look. In addition, seamless gutters are installed by a professional, whereas sectional gutters are available in hardware stores or can be used by an installer, in the case of certain materials.

You can install the gutters yourself instead of using the services of a professional installer; however, some options are only available to professionals. In addition, installing them is not an easy task, so youd better be prepared. You must pay attention to the slope so that water flows properly and doesnt remain stagnant, because if this is the case, the risk of water infiltration increases.

In order to reduce required gutter cleaning and prevent blockages that cause water infiltration, its possible to install gutter guards. Several gutter guard models can be installed to prevent debris from entering the gutter system, and this will also allow water to be properly drained. Depending on your needs and the environment surrounding your home, one of the installers from this list can direct you to the leaf guard that best suits your needs.

Read the original here:
Gutter installation

If youre thinking about installing and hanging gutters yourself, be careful. There are plenty of mistakes to be made. Improperly installed gutters can damage your house or even put your safety at risk in the wrong situation. Here are the five most common gutter mistakes, and how to avoid them:

There are a wide variety of gutter materials, sizes, styles, and gauges. Each has its benefits and drawbacks, but choosing the wrong one can be a nightmare. Choose the most durable material you can afford, and talk with your contractor or hardware store about roof shingle size and what width of gutter is right for your house. Standard residential homes typically use K style aluminum gutters, 5 or 6 inches wide from side to side, but if you live in a particularly rainy climate or looking for a different style gutter, other choices are available like round aluminum gutter . The gauge of a gutter is equally important, standard is 26 gauge but we recommend that you go with 32 gauge to be safe, particularly in regions that have extreme weather events (snow/ice, heavy rains, etc.)

Gutters may look perfectly even, but its a carefully crafted illusion. Gutters actually have a slight pitch that allows water to flow towards the downspouts, generally one to two inches of decline for every forty feet of length. Its very gradual and not noticeable, but it helps sweep away debris and keeps your gutters clean, and allows water to flow to the downspouts without overwhelming them, thus backing up the system. As you mount your gutters, check with a level to make sure theyre at the proper pitch.

All gutters are attached to your house by mounting system or different types of hangers (inside, outside, or strap), and the hangers need to be carefully spaced close together (3 feet or less) to give the gutter proper support. Without the correct support, the rain gutterswill sag. Water will collect in the lower places, tugging at your gutter system, until eventually the whole system will be ripped off your home. If using hangers, space according to instructions, or a bit closer if need be, and your gutters will stay where they belong, sending water to where it belongs.

Water runs down your roof, goes off the edge, so the gutter goes on the edge, right? Simple. And like so many things that seem simple, its actually wrong.

When choosing gutters, consider the material, as well as the size and width needed.

Your gutter needs to be a few inches under the edge of your roof. Why? Physics. If you put a paper towel on a drop of water, the water will be sucked into the fibers (a phenomenon called capillary action). Your roof does the same thing. Water will drip off the very edge of your roof, but also be pulled back up on the underside, and drip out a few inches underneath your roofs edge as well. A permanent solution you should consider is installing drip edge. Drip edge gets installed under the first course of shingles and promotes water to run freely from roof edge down into gutter. Without it, water may run down behind your gutter, down fascia board and siding, leading to potential damage.

Clogged gutters can result in runoff water, which can damage your home and landscaping. Gutter guards can prevent clogs and save you money. Download our free gutter guide

Finally, gutters will need to be welded or soldered together in order to be attached. But plan ahead in your construction to use as few welds as possible. Over time, the material in gutters, especially at the seams, is subjected to extreme temperature, force, and, of course, water. This puts a strain on any connections you solder or weld, and will eventually break the gutter if theyre not checked and touched up occasionally. The seams are the weak point in any gutter system, so treat them accordingly.

Seamless gutters or continuous rain gutters are another option available from contractors in some areas, so we highly recommend you consider having them installed on your home to avoid all the potential problems that welded together gutters can cause overtime.

As you can see, this can be tricky business. Dont go at it alone. Contact us today, a gutter installer wholl do the job right!

Original post:
Install Gutters Yourself? 5 Beginner Mistakes To Avoid ...

I was impressed by the way Gutterman, particularly Charles, addressed the repairs on my step-daughter's roof. The man knows his trade, and is not one to try to encourage repairs beyond what is needed. He found what needed to be done, and was clear about why and how he would... Read More

I was impressed by the way Gutterman, particularly Charles, addressed the repairs on my step-daughter's roof. The man knows his trade, and is not one to try to encourage repairs beyond what is needed. He found what needed to be done, and was clear about why and how he would make the repairs. He is very bright and well spoken, so there was no problem understanding the issues, and he was able to dumb them down for me. He also called me as requested prior to arriving so that I could meet him each time, and sent me texts of before-and-after photos. The day of the repairs, the temp was up to 100 degrees. I asked if I could bring him a drink, and he refused, saying, "We are professionals. We are prepared for this sort of thing". He also refused a tip. Lastly, it was clear to me that Charles is very loyal to Gutterman, which speaks to them as an employer, as well as to him. Although everyone I spoke to at Gutterman was efficient, it was Charles who makes Gutterman the kind of company who I will choose to do business with again.

See the original post here:
HOME - Northern Virginia Gutters Cleaning & Repair ...

For gutter installation and gutter repair services, count on MasterWorks Painting & Remodeling. Our home improvement contractors can repair gutters or install a gutter system that is completely new on your home or business. Gutters can become damaged over time from harsh weather. If you have a small gutter problem, we can provide you with expert gutter repair services. For larger problems, it may be time to install a gutter system that is completely different than your current one. Contact us at (703) 263-3302 to receive an estimate on your gutter installation or gutter repair services in Fairfax, Vienna, Reston, Chantilly, Ashburn, Oakton, or the surrounding Virginia area.

MasterWorks Painting & Remodeling understands the importance of a proper gutter installation. If you properly install gutters, it will protect your home from foundation problems, mold, and mildew. A proper gutter installation must have the vertical downspouts directed away from your home. This will shoot the water toward a drainage area, rather than towards your foundation. Let us help you select the best gutter system for your home. Call us at (703) 263-3302 to receive an estimate on our gutter installation services today.

It takes a lot to maintain a gutter system. Homeowners must clean leaves, roof shingle particles, and other debris from the gutters to ensure they work properly. No matter how often you clean and maintain your gutters, a strong wind or harsh storm can cause damage to them. When your gutters are damaged, you can count on MasterWorks Painting & Remodeling to provide expert gutter repair services. Youll be surprised at what a huge difference a simple gutter repair can make in the way your gutters operate. Call us at (703) 263-3302 to receive an estimate on gutter repair services today.

MasterWorks Painting & Remodeling provides many other home improvement and remodeling services aside from gutter repair and gutter installation services. You can count on us for kitchen remodeling, basement finishing, new windows, siding installation, and many other home improvement services. Whether you need Fairfax painting services or bath remodeling in Vienna VA, our contractors will meet your home improvement and remodeling needs. Contact us at (703) 263-3302 to receive an estimate on your gutter installation, gutter repair, or other home improvement service in Vienna, Fairfax, Reston, Chantilly, Ashburn, Oakton, or a nearby Virginia area.

Read the original here:
Gutter Installation | Fairfax | Ashburn | Oakton | Reston ...

Step 1: Planning the projectCompleted rain gutter

Almost all home centers and full-service hardware stores sell guttering that is designed primarily for easy installation. But with just a little bit more work, you can use these same parts to put together rain gutters and downspouts that are stronger and better looking too.

Evaluate and plan the projectGutter replacement, which involves installing your own rain gutters can save you substantially over professionally installed gutters, but there are a few pitfalls to watch out for. Inspect the fascia and soffit (Fig. B) for signs of rotted wood, which will need to be replaced before you put up the rain gutters. Many houses have a trim board or crown molding nailed to the fascia just under the shingles. Youll have to either remove this as we did or add a continuous strip of wood under it to create a flat plane for the gutters. In either case, prime and paint bare wood before you hang the gutters.

Fig. A shows an example of a rain gutter system for a typical house. Record the length of the rain gutter runs and mark the downspout locations. Then count up the inside and outside corners and end caps (note whether they are right or left ends). Measure the height of downspouts and add 4 ft. to each for the extension away from the house at the bottom. Each downspout requires three elbows. There are two types of elbows that turn either to the front or side of the downspout. Most installations require only front elbows, but occasionally you may need a side elbow, usually to turn the downspout extension sideways. Here are a few planning tips:

Cut the front and back sides with tin snips. Bend the gutter and cut the bottom.

Cut a 2-in. long notch in the front lip of the gutter with tin snips to join a rain gutter section with an inside or outside corner piece. (Cut a 4-in. long notch to overlap and splice together gutter sections.)

Lay a bead of gutter sealant along the corner 1-1/2 in. back from the edge. Hook the front lip of the corner over the notched section of gutter and snap it over the gutter.

Join the gutter to the corner with six rivets in the locations shown. Start by drilling a 1/8-in. hole (for 1/8-in. rivets) at the front of the gutter and installing the first rivet with the rivet gun. Now drill the remaining holes and install the rivets.

Caulk the seam on the inside of the rain gutter with gutter sealant. Put a dab of sealant over each rivet.

Preassemble before installing guttersIts much easier to join sections on the ground than to work from the top of a ladder. Photos 1 8 show how. Instead of butting parts together and covering the joints with a seam cover as recommended by the manufacturer, lap all seams from 2 to 4 in. Then caulk and rivet them together (Photos 3 5). Weve shown joining a gutter section to a corner. Use the same process to join two sections of gutter, except overlap the pieces at least 4 in. When youre splicing gutter sections, plan ahead to leave the best-looking factory-cut end on the outside if possible. Also lap the rain gutters so the inside section is facing downhill to prevent water from being forced out the seam.

Where a gutter ends, cut it to extend about an inch past the end of the fascia board to catch water from the overhanging shingles. Then attach an end cap with rivets and seal the joint from the inside with gutter sealant.

Mark the center of the downspout outlet on the bottom of the gutter. Center the outlet, flange side down, over the mark and trace around the inside. Cut a V-shaped notch with an old chisel as a starting hole for the tin snips. Place two short scraps of 24 side by side under the gutter to support it while you chisel the notch.

Cut out the outlet hole with offset tin snips. Red tin snips cut counterclockwise. Green snips cut clockwise. Either one will work. Cut 1/16 in. outside the line.

Slip the outlet into the hole and predrill 1/8-in. holes for the rivets. Remove the outlet and run a bead of gutter sealant around the opening. Press the outlet into the caulked opening and install the rivets.

Cut in downspout tubes at each downspout location

First measure from the corner of the house to the center of your chosen downspout location. Double-check for obstructions. Transfer this dimension to the gutter and cut in a downspout outlet (Photos 6 8). This method takes a few minutes longer than using one of the short gutter sections with a preinstalled outlet, but it eliminates two seams and looks much neater. You can make this cutout with a duckbill tin snips, but a special offset snips like were using (available from hardware stores and home centers) is much easier for beginners.

When installing gutters, set the proper slope by driving a nail 1/2 in. below the shingles on the high side of the gutter run. Measure and record the distance from the bottom of the fascia board to this nail. Subtract 1/4 in. for every 10 ft. of gutter from this measurement and mark this distance at the low end of the gutter run. Drive a nail at this mark and stretch a chalk line between the two nails. Align a level with the string to check the slope. The bubble should be off-center toward the high side. If its not, adjust the string until the bubble indicates that you have the proper slope. Finally, snap the string to mark a line on the fascia board.

Drive 1-1/4 in. stainless steel hex head sheet metal screws through the back of the gutter into the fascia. Install one screw every 2 ft.

A little slope is all you need

The number and size of downspouts determines how fast your gutters will empty. Sloping them helps eliminate standing water that can cause corrosion and leak through the seams. Slope each gutter run down toward the downspout about 1/4 in. for every 10 ft. of gutter. If your fascia boards are level, you can use them as a reference for sloping the gutters. Check this by holding a level against the bottom edge. If they arent level, adjust the string line until a level aligned with it shows a slight slope (Photo 9). Snap a chalk line to indicate the top of the gutter. Then straighten gutter sections as you screw them to the fascia by aligning the top edge with the chalk line (Photo 10).

Slide gutter flashing under the shingles and secure with 1-in. roofing nails every 2 ft. Lap sections about 2 in.

Hook a hanger under the front lip of the gutter and screw it through the flashing into the fascia. (The gutter apron will prevent you from slipping the hangers over the back edge of the gutter as intended.) Install hangers every 2 ft.

With gutter replacement, you can prevent water from running behind your gutters by installing a metal gutter apron flashing under the shingles and over the back edge of the gutter (Photo 11). If your home center or hardware store doesnt sell prebent flashing, ask an aluminum siding contractor or local sheet metal fabricator to bend some for you. Ideally the flashing should be slid under both the shingles and the roofing paper or ice and water barrier. If this isnt possible because the ice and water barrier is stuck to the sheathing, or there are too many nails and staples along the edge of the roofing paper, then just slip the flashing under the shingles (Photo 11). If the flashing youre using is too short to reach down over the back edge of the gutter, slip an additional strip of sheet metal flashing under the bent flashing and over the gutters.

Install hidden hangers

With the gutters screwed to the fascia, its a simple job to install the hidden gutter hangers (Photo 12). Install hangers every 2 ft. to support the gutters and strengthen the front edge. The hangers are designed to slip over the back edge of the gutter, but since weve covered this edge with flashing, just hold them level and drive the screws through the flashing and gutter back into the fascia. The large screws included with the hangers we used are a little tricky to get started, especially through steel gutters and flashing. Spin them at high speed without applying much pressure until the screw tip bites into the metal. Then lean on the drill and drive them into the fascia.

Screw an elbow to the downspout outlet. Hold another elbow against the wall and measure between them. Allow for a 1-1/2 in. overlap at each end. Use a hacksaw to cut this length from the uncrimped end of a downspout tube.

Crimp one end of the short length of downspout with a special sheet metal crimper. With the three blades on the inside of the tube, hold the crimper against the inside corner of the tube and squeeze. Crimp three times across both long edges and twice on the narrow sides. Attach this short section of downspout to the two elbows with two 1/4-in. hex head sheet metal screws into each joint.

Cut strips about 1-1/4 in. wide from the end of a downspout with tin snips. Cut out a U-shaped bracket and snip off the corners. Measure from the corner of the house and mark the locations of each bracket, spacing them about 6 ft. apart. Attach the brackets to the house with stainless steel screws. (Drill a clearance hole through stucco with a masonry bit. Use plastic anchors for brick. Use 1/4-in.-long hex head screws for vinyl siding.) Cut and screw downspout sections to an elbow at the bottom. The bottom of the elbow should be about 6 in. above the ground. Slip this assembled downspout section over the crimped end of the top elbow and secure it with two screws.

Drive screws through the brackets into the assembled downspout. Complete the assembly by adding a length of downspout tube to the bottom elbow to direct water away from the foundation.

Photos 13 16 show how to install the downspouts. Were using standard 2 x 3-in. downspouts, but the procedure for oversized 3 x 4-in. ones is the same. Assemble the elbows and downspout tube with the crimped ends facing down to prevent water from leaking out of the joints. Use sheet metal screws rather than rivets so you can disassemble the downspouts to clean them if necessary. Pros prefer prepainted 1/4-in. hex head screws with very sharp points, called zippers because theyre easy to install. We found these screws in the aluminum siding section of a home center, but a gutter supplier would be another good source.

You can cut downspout tubing with a 32-tooth hacksaw blade, but the pro we talked to uses a circular saw with a standard 24-tooth carbide blade. A power miter box also works great for cutting both gutters and downspouts. Use an old blade, though. Protect yourself from flying bits of metal with goggles, leather gloves, jeans and a long-sleeve shirt.

Each length of gutter and every elbow is squeezed, or crimped, on one end to allow the pieces to fit together, one inside the other. Since 10-ft. lengths of downspout are only crimped on one end, youll have to crimp one end of any cutoff piece to make it fit inside the next elbow or downspout section. If you only have one or two downspouts to install, you can use a needle-nose pliers to twist crimps into the end. But an inexpensive crimping tool will save you tons of time and frustration (Photo 14).

Finish the gutter job by easier to hang the downspouts. attaching the downspouts to the wall. If you cant find U-shaped brackets, make them from sections of downspout (Photo 15). They look better than the bands that wrap around the outside and make it easier to hang the downspouts.

After installing gutters, gutter maintenance is the key to long-lasting gutters

Clean leaves from your gutters twice a year, or hire a company that specializes in gutter cleaning and maintenance. Youll extend the life of your gutters and eliminate problems like backed-up gutters and plugged downspouts.

Ten-foot lengths of metal gutters, downspouts and accessories are available at home centers, lumberyards and full-service hardware stores. Standard colors are brown and white. Matching inside and outside corners, downspout elbows and accessories are also available. Buy special gutter sealant to seal the seams. Its available in small toothpaste-type tubes or 12-oz. caulk gun tubes.

Using many of the same basic techniques we show in this story, you can install your own seamless gutters. Listed under Gutters in the Yellow Pages, many seamless gutter companies will come to your house, measure and form continuous lengths of aluminum gutter to fit, and sell you all the installation accessories youll need. It costs a little more, but youll be able to choose from dozens of colors and eliminate seams in the gutter runs. Youll also save the hassle of measuring, shopping and hauling the parts home in your VW bug.

Have the necessary tools for this DIY project lined up before you startyoull save time and frustration.

Avoid last-minute shopping trips by having all your materials ready ahead of time. Heres a list.

Originally posted here:
Gutter Replacement: How to Install Gutters The Family ...

Steps // How to Install Rain Gutters

3Attach fascia brackets

Step Three // How to Install Rain Gutters

Photo by Mary Beth Montgomery

Locate the rafter tails behind the fascia; they're typically spaced 16 inches on center (look for telltale nail heads).

Make a mark at the chalk line on every other rafter tail.

Bore a -inch-diameter pilot hole through the fascia and into the rafter tail at each mark.

Fasten fascia brackets with -inch stainless steel lag screws long enough to penetrate rafters 2 inches (as shown).

Tip: Rub soap on the lag screws so they'll be easier to drive through fascia and into rafter tails.

4Saw gutter to length

Step Four // How to Install Rain Gutters

Photo by Mary Beth Montgomery

Cut gutter section to length with hacksaw and aviation snips, or with a 12-inch power miter saw fitted with a carbide-tipped finish blade (as shown).

If the gutter continues around a corner, cut the appropriate angle (typically 45 degrees) on that end.

If the run requires two sections of gutter, overlap them by 8 inches and use 3/8-inch-long, self-tapping, stainless steel screws or pop rivets, in two rows of four each, to join them.

Tip: Locate screws or rivets in the sides of the gutter, never in the bottom.

8Form strip-miter joint at corner

Step Eight // How to Install Rain Gutters

Photo by Mary Beth Montgomery

Cover the joint between two lengths of gutter at each corner with a strip miter a 3-inch-wide strip of aluminum.

Wrap the aluminum strip tight around the underside of the gutter. Secure it with eight pop rivets or sheet- metal screws.

Cut a triangular section from the top of the strip miter (as shown) with snips, and then fold down the two flaps around the top edge of the gutter.

This joint can also be made more waterproof with the addition of a high-quality siliconized caulk.

9Connect downspout to gutter

Step Nine // How to Install Rain Gutters

Photo by Mary Beth Montgomery

Secure the downspout outlet to the gutter with four pop rivets or screws.

Screw a downspout elbow to the outlet tube protruding down from the gutter.

Hold another elbow against the house and cut a piece of downspout to fit between the two elbows.

Use needlenosed pliers to slightly crimp the elbow to fit into the downspout (as shown).

Fasten the parts together with pop rivets or screws.

Tip: Use two downspout brackets on a one-story house and three brackets on a two-story house.

Here is the original post:
How to Install Rain Gutters | This Old House

Recent Job Requests for Install or Replace Gutters Contractors in Ashburn, Virginia:

Project Location: Ashburn, VA 20147

Date: 06/23/2018

Project Description: Replace existing gutters

Select the type of gutter material you want:: Seamless Aluminum

Request Stage: Planning & Budgeting

Desired Completion Date: 1 - 2 weeks

What kind of location is this?: Home/Residence

Comment: Would like to do replacement with a gutter cover system of some type ...

Project Location: Ashburn, VA 20147

Date: 06/22/2018

Project Description: Replace existing gutters

How many stories is your house?: 3

Request Stage: Planning & Budgeting

Desired Completion Date: 1 - 2 weeks

What kind of location is this?: Home/Residence

Project Location: Ashburn, VA 20147

Date: 06/15/2018

Project Description: Replace existing gutters

Select the type of gutter material you want:: Don't Know

How many stories is your house?: 2

Request Stage: Planning & Budgeting

Desired Completion Date: 1 - 2 weeks

What kind of location is this?: Home/Residence

Property Owner: Yes

Comment: Need to replace gutters.

Project Location: Ashburn, VA 20148

Date: 06/13/2018

Project Description: Replace existing gutters

Select the type of gutter material you want:: Galvanized steel

How many stories is your house?: 2

Request Stage: Ready to Hire

Desired Completion Date: Timing is flexible

What kind of location is this?: Home/Residence

Property Owner: Yes

Comment: Replace existing gutter

Project Location: Ashburn, VA 20147

Date: 06/11/2018

Project Description: Replace existing gutters

Select the type of gutter material you want:: Copper

How many stories is your house?: 2

Request Stage: Planning & Budgeting

Desired Completion Date: Timing is flexible

What kind of location is this?: Home/Residence

Property Owner: Yes

Project Location: Ashburn, VA 20147

Date: 06/11/2018

Project Description: Replace existing gutters

Select the type of gutter material you want:: Don't Know

How many stories is your house?: 2

Request Stage: Planning & Budgeting

Desired Completion Date: 1 - 2 weeks

What kind of location is this?: Home/Residence

Property Owner: Yes

Comment: Need to replace gutters.

Project Location: Ashburn, VA 20147

Date: 06/09/2018

Project Description: Install new gutters where there are none

Select the type of gutter material you want:: Seamless Aluminum

Request Stage: Ready to Hire

Desired Completion Date: 1 - 2 weeks

What kind of location is this?: Home/Residence

Comment: Install new gutters in the back of the house. two sections: bump out and kitchen.

Project Location: Ashburn, VA 20147

Date: 06/01/2018

Project Description: Replace existing gutters

Select the type of gutter material you want:: Don't Know

How many stories is your house?: 2

Request Stage: Ready to Hire

Desired Completion Date: Timing is flexible

What kind of location is this?: Home/Residence

Property Owner: Yes

Comment: I am seeking to get a quote on replacing my gutters.

Project Location: Ashburn, VA 20148

Date: 05/2018

Project Description: Replace existing gutters

Select the type of gutter material you want:: Don't Know

Request Stage: Ready to Hire

Desired Completion Date: Timing is flexible

What kind of location is this?: Home/Residence

Project Location: Ashburn, VA 20148

Date: 05/2018

Project Description: Replace existing gutters

How many stories is your house?: 2

Request Stage: Planning & Budgeting

Desired Completion Date: Within 1 week

What kind of location is this?: Home/Residence

Property Owner: Yes

Comment: Gutters are old and need to be replaced. I need an estimate for the project

Project Location: Ashburn, VA 20148

Date: 05/2018

Project Description: Replace existing gutters

Request Stage: Planning & Budgeting

Desired Completion Date: Timing is flexible

What kind of location is this?: Home/Residence

Property Owner: Yes

Comment: REPLACE METAL GUTTERS

Project Location: Ashburn, VA 20148

Date: 05/2018

Project Description: Replace existing gutters

Continue reading here:
Gutter Installers in Ashburn, VA - HomeAdvisor

In my correspondence with home owners, GutterWorks has received many request for a guide so they can be better educated when purchasing a seamless gutter system.

This check sheet is provided for the homeowner so they can better evaluate the installation quotes they receive.

There are two categories: Material & Installation. They will be graded using Poor, Good and Excellent.

When evaluating this list you will need to keep in mind that different parts of the country may require a better grade of product. For example, in the North half of the U.S. we may encounter a ice build up in and on the gutter. This extra weight will require either a stronger hanger or more hangers to hold this extra weight for a extended period of time.

A 1" to 2" slope in 40 foot. NOTE: A gutter installed level will drain because water levels itself, however you will not have any water flow to self clean the gutter. Too much slope does not look good and you loose some of the gutters holding capacity.

Example: A gutter sloping 3 1/2" in a run has lost 1/2 of its holding capacity. In a short heavy down pour the water at the high end of the gutter will be nearly to the bottom of the gutter and at the downspout end (Low end) the water will be overflowing the top of the gutter, Remember- water levels itself.

Summary: Try to strike a happy medium, some slope for cleaning but not too much.

2x3 Downspout will drain 600 sq. ft of roof area.3x4 Downspout will drain 1200 sq. ft. of roof area.

One foot of 5" K-Style gutter holds 1.2 gallons of water.One foot of 6" K-Style gutter holds 2.0 gallons of water.

This is a important part of installation on homes of 3/12 and 4/12 pitch roof. Water will suck back (capillary action) on the roofing material and run down the face board and behind the gutter (causing damage to the face board over time). The basic knowledge and understanding of capillary action of water was the founding principle that the inventor Robert Demantini used in producing the well known product "GUTTER HELMET" which started a revolution in gutter cover industry spurring dozens of different models of gutter covers we see on the market today.

Steeper sloped roofs do not have this problem and in some cases the singles may overhang the drip edge and droop down into the gutter thus eliminating the problem . Strip flashing must be used to bridge the gap between the drip edge and the back of the gutter if the gutter runs below the drip edge at the lower end of the gutter run. Good luck in getting a shoddy gutter company to come back and fix this problem because it will require reinstalling the complete gutter system or installing flashing. So beware and insist that it be done!

Consider some kind of gutter guard. In most cases if you have your gutter installer install the gutter guard when he's there to install the gutter, they'll cut you a better deal. Use 3x4 downspout. DO NOT INSTALL PRODUCTS THAT FIT DOWN INTO THE GUTTER. Install only Product that fit and install on top of the gutter. Metal products will last longer than a Plastic product. No rolled metal or plastic screens!

A brief comment about trying to clean your gutters from the ground. There are mechanical devices that do work. The water blasters are poor at best. Its very hard to clean something when you can't see what your doing. The next time you take your car to the car wash close your eyes when you wash it and see what it looks like when your finished. And O' yes don't forget the rain coat when you use the water blaster on your gutter because mother natures gravity is going to bring everything straight down on your head- and pick a calm day or the windows may have to be re-cleaned as well. BEEN THERE, DONE THAT!

Screws: Stainless Steel with painted heads: Excellent Zinc Coated with painted heads: Good Pop Rivets: Excellent

More:
Seamless Gutter Installation Check Sheet | Front Street ...