Common Codes – Fast Water Heater Company

Fast Water Heater Company performs installations as safely as possible to protect you and your family. Due to various injuries and accidents related to water heaters over the last ten years, most cities and counties have adopted either the 2006, 2009 or 2012 Uniform Plumbing Code (or in the case of California, the California Plumbing Code).

When we perform your installation, we will inspect your water heater and ensure it is up to date on all relevant safety codes.

Also, on the back of your invoice, you will find a list of all of the state codes that are relevant for your installation.

Some examples of common water heater codes include:

An expansion tank is required if a plumbing system is closed, which means that the back-flow that normally runs between the house and the main water supply, is blocked. However, when water is heated, it starts to expand, which causes a rise in water pressure.

The increased pressure must go somewhere. If there is nowhere for the pressure to go, it places extra stress and strain on your water heater and your homes plumbing system. Increased pressure will shorten the life of your water heater. However, expansion tanks provide relief from this excess water pressure and protect your home.

A water pressure PSI test will determine if you need an expansion tank or not.

In all our service locations, we install water heaters with earthquake straps to ensure your safety in the event of a natural disaster. Because the West Coast is in earthquake zones, all installations include straps on the top- and bottom-third of the water heater.

If your water pressure is above 80 PSI, its recommended to install a pressure regulating valve. As population density increases, water pressure goes up as well. However, high water pressure can damage your plumbing and fixtures, including your hot water heater. This can cause a premature crack in the glass lining of the water heater. Pressure regulating valves will prevent unnecessary stress on your plumbing system.

Its generally recommended, and required, to install a drip pan with a drain line beneath your hot water heater tank. Especially if you water heater is in your home or basement, a leak could cause lots of water damage. A pan and drain eliminate this possibility.

Installing a dedicated water shutoff on your water heater will allow you to turn off water to your heater, but not to your entire home. This way, if you ever need to service your water heater, you wont be inconvenienced with having to turn off the water to the rest of your house.

In some areas, the P&T (pressure and temperature relief) valve is required to be piped to the exterior. The P&T valve goes off when your hot water temperature exceeds 210 degrees Fahrenheit or 150 PSI. Some areas will allow you to pipe the P&T within 6 of a garage floor. The advantage of this is that if the P&T valve is going off, it usually means your water heater has a problem and its good to know about it. The disadvantage is that when the P&T does go off, the water comes out at very high temperature and high pressure. It is dangerous to allow children, for example, to play around the P&T valve. Due to accidents, some areas require the valve to be piped to the exterior.

In addition to placement in a certain area, the CO emissions of a water heater require it be properly vented. This will prevent any CO from entering your home and living areas. The vents must be made of a proper material and keep specific clearance from combustible materials.

Gas water heaters emit carbon monoxide (CO) when they run. 10,000 people die in the U.S. every year from CO poisoning so its important the water heater is placed in approved location. For example, in some areas, water heaters are not allowed to be installed in closets, unless they are only used for the water heater.

Codes require us to place a sediment trap on the gas line into the water heater as close to the inlet as possible. This is to prevent moisture and debris from entering the firing chamber of the hot water heater.

For electric tanks in unheated spaces, the tank must be placed on an incompressible, insulated surface with a minimum thermal resistance of R-10. This bottom board is to help prevent heat loss from the bottom of an electric water heater and can increase energy efficiency.

Contact us for more information about water heater codes in your jurisdiction!

This company is great. I have had two water heaters installed and one follow up warranty service which I think went very well. Both of the service professionals I have met and everyone I have spoken to is also very professional. I can recommend this company with complete confidence.- Suzan H. via YelpWe needed a replacement (and fast!). FAST Water Heater Co. was here in 1 hour, provided an estimate, told me exactly what it would take to comply with current code, and completed the job very quickly and professionally. No surprises...now I can take a shower! I would recommend FAST Water Heater Co. without hesitation.- Jeff H. via GoogleMatt Smith did an outstanding custom water heater/thermal expansion tank installation job under a stairwell. He was able to fabricate the installation so that I still was able to gain access to the storage space behind the water heater. I give him 5+ stars.- Tom J. via FacebookFast is the operative word here. I called to have my water heater replaced and they were at my house within 1 hour. There were some challenges with replacing my tank and Dan confidently suggested my options. In and out in a couple of hours with zero inconvenience! Dan was super personable and very trustworthy! - Anonymous via SuperPages

More here:
Common Codes - Fast Water Heater Company